OEE on VFFS Packaging Lines: How to Measure and Improve It

Plant managers at larger food and FMCG companies rarely ask how fast a packing machine can run. They ask how much good product it packs in a shift. The gap between those two answers is where money is lost, and the standard way to measure that gap is overall equipment effectiveness, or OEE. A packaging line with a high rated speed but a poor OEE is a slow line in practice. A line with a modest rated speed and a high OEE often packs more.

This guide explains how to calculate OEE on a vertical form fill seal (VFFS) line, where the typical losses hide, and what a plant can do to raise output without buying another machine. It is written for plant heads, production managers and engineers who want a method they can use on Monday morning.

What OEE Measures

OEE tells you what share of your scheduled production time is truly productive. It multiplies three factors, each shown as a percentage.

  • Availability: the share of planned time the machine actually runs. Breakdowns, film changes, changeovers and waiting for material reduce it.
  • Performance: how close the machine runs to its ideal speed while it is running. Slow running, small stops and jams reduce it.
  • Quality: the share of packs that are good on the first pass. Rejected packs, bad seals, underweight and misprints reduce it.

The formula is simple: OEE = Availability × Performance × Quality. A machine that is available 90 percent of the time, runs at 85 percent of its ideal speed and makes 98 percent good packs has an OEE of about 75 percent (0.90 × 0.85 × 0.98). Many plants are surprised to find their real figure sits lower than they expected, and that is exactly why the measurement is useful.

A Worked Example (Illustrative Numbers)

Take a single VFFS line on an eight hour shift. The figures below are examples, not benchmarks, so replace them with your own data.

Item Value
Planned production time 480 minutes
Stops (changeover, film change, breakdowns) 60 minutes
Run time 420 minutes
Ideal speed 60 packs per minute
Total packs made 21,000
Good packs 20,370
  • Availability = 420 / 480 = 87.5 percent.
  • Performance = 21,000 / (420 × 60) = 83.3 percent.
  • Quality = 20,370 / 21,000 = 97 percent.
  • OEE = 0.875 × 0.833 × 0.97, which is about 70.7 percent.

The result shows that performance is the weakest factor in this example. The plant loses more through slow running and small stops than through long breakdowns, so the improvement effort should start there.

The Six Big Losses on a VFFS Line

Lean practice groups losses into six categories. Each has a typical form on a form fill seal line.

  1. Breakdowns: a failed heater, a broken belt or a servo fault that stops the machine for a long time.
  2. Setup and changeover: changing film rolls, pouch size, forming tube or product, plus cleaning between products.
  3. Small stops: film tracking errors, product caught in the seal, sensor trips and hopper starvation.
  4. Reduced speed: running below the rated speed because the seal quality or weight accuracy suffers at higher speed.
  5. Start-up rejects: packs wasted while the machine warms up and settles after a stop.
  6. Production rejects: packs with weak seals, wrong weight or print registration faults.

Track each loss in minutes or packs for two weeks. A simple tally sheet at the machine is enough. The pattern usually shows that two or three causes account for most of the loss.

How to Improve Availability

Availability improves when machines stop less and restart faster.

  • Plan film changes. Keep the next roll ready at the machine and train operators to splice quickly. A film splicing option cuts the stop further.
  • Standardise changeovers. Use a written checklist, mark set positions, and keep forming tubes and change parts in labelled racks. Parallel tasks, such as one person cleaning while another sets the film, shorten the stop.
  • Prevent breakdowns. Replace wear parts such as sealing jaw heaters and belts on a schedule instead of waiting for failure. Our VFFS machine troubleshooting guide lists daily checks that catch most problems early.
  • Stock critical spares. A heater or sensor in the store turns a half-day stop into a ten-minute repair.
  • Keep the line fed. If the packer waits for product, the problem is upstream. Check the feeder, hopper level sensor and conveyor.

How to Improve Performance

Performance losses are the hardest to see because the machine appears to be working. Fix them with these steps.

  • Find the cause of micro stops. Log the reason each time the machine pauses, even for seconds. Most small stops come from film tracking, product in the seal area or a dirty sensor.
  • Match the filler to the product. A servo auger filler for powders or a multihead weigher for snacks and granules keeps dosing steady at higher speed. Read our comparison of multihead, auger and cup fillers to choose well.
  • Tune the seal. Set temperature, dwell time and pressure to the film. A seal that is too cold leaks, and one that is too hot burns the film, and both slow the line as operators reduce speed to compensate.
  • Use the right motion type. A continuous motion machine suits high-volume pillow packs, while intermittent motion suits a wider range of pack styles and weights.

Machine design affects the ceiling. Our GT-5s is a continuous motion machine with five servos and a capacity of up to 180 pouches per minute for centre seal pillow packs. The Komet Sprint is an intermittent motion machine with three servos, reaching up to 100 pouches per minute across several pack styles. Choosing the model that fits your pack mix helps the line run closer to its rated speed.

How to Improve Quality

Quality losses cost both product and film, so they hit margin twice.

  • Check weights on a schedule. Weigh a sample of packs every half hour, record the average and spread, and adjust the filler before the average drifts out of tolerance.
  • Inspect seals. Pull and visual checks at the start of each run and after every film change catch leaks early.
  • Control the film. Poor tracking, wrong tension or variable film thickness leads to wrinkled seals and misprints. Keep film stored in clean, dry conditions.
  • Protect the product. For snacks, nuts and other products that go stale, nitrogen flushing keeps oxygen low. Our guide on nitrogen flushing in food packaging explains how it works.
  • Add inline checks. A checkweigher or metal detector catches faults before they leave the plant.

Set Realistic OEE Targets

Many plants quote a world-class OEE figure of around 85 percent, but a realistic target depends on the product and the number of changeovers. A line that runs one product all week will reach a higher number than a line that changes SKUs five times a day. Set a baseline first, then aim for steady gains of a few points each quarter. Compare each line with its own past performance rather than with another plant that has a different product mix.

When a Better Machine Is the Real Answer

Process fixes can only go so far. If the machine is old, the controls are limited or spare parts are hard to find, the cheapest improvement may be a newer line. Look for servo driven sealing and pulling, a modern motion controller, recipe storage and easy access for cleaning. To judge the financial case, use our guide to calculating packaging machine ROI, which shows how to turn the saved minutes and packs into a payback period.

Talk to VS Packit About Your Line

VS International (VS Packit) designs and builds VFFS machines in Faridabad for food, FMCG, snack, spice, flour and pharma producers. If you want to raise the OEE of an existing line, or you plan a new one, send us your product, pack size and target output through our contact page. Our engineers can suggest a model and a filler, run a trial on your product and help you set a realistic target.


Frequently Asked Questions

Quick answers to common questions about this topic.

What is OEE in a packaging line?

+
OEE, or overall equipment effectiveness, shows what share of scheduled time is truly productive. It is calculated as availability multiplied by performance multiplied by quality, and it exposes losses from stops, slow running and rejected packs.

How do you calculate OEE for a VFFS machine?

+
Divide run time by planned time for availability, divide actual packs by ideal packs for performance, and divide good packs by total packs for quality. Multiply the three to get OEE.

What is a good OEE for a packaging line?

+
A common reference figure is about 85 percent, but a realistic target depends on your product and how often you change over. Set your own baseline first and improve steadily from there.

What causes the most losses on a VFFS line?

+
Typical causes include film changes and changeovers, small stops from film tracking or product in the seal, reduced running speed, and rejects from weak seals or wrong weights. Logging stops for two weeks shows which ones matter most in your plant.

How can I raise OEE without buying a new machine?

+
Standardise changeovers, plan film changes, replace wear parts on schedule, tune the seal settings, check weights regularly and fix the causes of small stops. These steps often give gains of several points.

Can VS Packit help improve my line efficiency?

+
Yes. Share your product, pack and target output through our contact page, and our engineers can recommend a machine or upgrade and run a trial on your product.
Phone WhatsApp Contact Us